مقاله انگلیسیElectrical conductor

Electrical conductor

From Wikipedia, the free encyclopedia
  (Redirected from Conductor (material))
Jump to: navigation, search

In physics and electrical engineering, a conductor is a material which contains movable electric charges. In metallic conductors, such as copper or aluminum, the movable charged particles are electrons (see electrical conduction). Positive charges may also be mobile in the form of atoms in a lattice that are missing electrons (known as holes), or in the form of ions, such as in the electrolyte of a battery. Insulators are non-conducting materials with fewer mobile charges, which resist the flow of electric current.

All conductors contain electric charges which will move when an electric potential difference (measured in volts) is applied across separate points on the material. This flow of charge (measured in amperes) is what is meant by electric current. In most materials, the direct current is proportional to the voltage (as determined by Ohm's law), provided the temperature remains constant and the material remains in the same shape and state.

Most familiar conductors are metallic. Copper is the most common material used for electrical wiring. Silver is the best conductor, but is expensive. Because it does not corrode, gold is used for high-quality surface-to-surface contacts. However, there are also many non-metallic conductors, including graphite, solutions of salts, and all plasmas. There are even conductive polymers. See electrical conduction for more information on the physical mechanism for charge flow in materials.

All non-superconducting materials offer some resistance and warm up when a current flows. Thus, proper design of an electrical conductor takes into account the temperature that the conductor needs to be able to endure without damage, as well as the quantity of electric current. The motion of charges also creates an electromagnetic field around the conductor that exerts a mechanical radial squeezing force on the conductor. A conductor of a given material and volume (length × cross-sectional area) has no real limit to the current it can carry without being destroyed as long as the heat generated by the resistive loss is removed and the conductor can withstand the radial forces. This effect is especially critical in printed circuits, where conductors are relatively small and close together, and inside an enclosure: the heat produced, if not properly removed, can cause fusing (melting) of the tracks.

Thermal and electrical conductivity often go together. For instance, most metals are both electrical and thermal conductors. However, some materials are practical electrical conductors without being good thermal conductors.

Contents

[hide]

[edit] Conductor size

In many countries, conductors are measured by their cross section in square millimeters. However, in the United States, conductors are measured by American wire gauge for smaller ones, and circular mils for larger ones.

[edit] Conductor materials

Of the metals commonly used for conductors, copper has a high conductivity. Silver is more conductive, but due to cost it is not practical in most cases. However, it is used in specialized equipment, such as satellites, and as a thin plating to mitigate skin effect losses at high frequencies. Because of its ease of connection by soldering or clamping, copper is still the most common choice for most light-gauge wires.

Aluminium has been used as a conductor in housing applications for cost reasons. It is actually more conductive than copper when compared by unit weight, but it has technical problems that have led to problems when used for household and similar wiring, sometimes having led to structural fires:

  • a tendency to form an electrically resistive surface oxide within connections, leading to heat cycling of the connection (unless protected by a well-maintained protective paste);
  • a tendency to "creep" under thermal cycling, causing connections to get looser due to a low mechanical yield point of the aluminium; and
  • a coefficient of thermal expansion sufficiently different from the materials used for connections, accelerating the creep problem and addressed by using only plugs, switches, and splices rated specifically for aluminium.

These problems do not affect other uses, and aluminium is commonly used for the low voltage "drop" between a power pole and the household meter. It is also the most common metal used in high-voltage transmission lines, in combination with steel as structural reinforcement.

The surface of anodized aluminium does not conduct electricity, and sometimes this must be considered when aluminium enclosures are to be electrically bonded for safety or to enclose or exclude electromagnetic radiation.

[edit] Conductor ampacity

The ampacity of a conductor, that is, the amount of current it can carry, is related to its electrical resistance: a lower-resistance conductor can carry more current. The resistance, in turn, is determined by the material the conductor is made from (as described above) and the conductor's size. For a given material, conductors with a larger cross-sectional area have less resistance than conductors with a smaller cross-sectional area.

For bare conductors, the ultimate limit is the point at which power lost to resistance causes the conductor to melt. Aside from fuses, most conductors in the real world are operated far below this limit, however. For example, household wiring is usually insulated with PVC insulation that is only rated to operate to about 60 °C, therefore, the current flowing in such wires must be limited so that it never heats the copper conductor above 60 °C, causing a risk of fire. Other, more expensive insulations such as Teflon or fiberglass may allow operation at much higher temperatures.

The American wire gauge article contains a table showing allowable ampacities for a variety of copper wire sizes.

[edit] Isotropy

If an electric field is applied to a material, and the resulting induced electric current is in the same direction, the material is said to be an isotropic electrical conductor. If the resulting electric current is in a different direction from the applied electric field, the material is said to be an anisotropic electrical conductor.


نظرات شما عزیزان:

نام :
آدرس ایمیل:
وب سایت/بلاگ :
متن پیام:
:) :( ;) :D
;)) :X :? :P
:* =(( :O };-
:B /:) =DD :S
-) :-(( :-| :-))
نظر خصوصی

 کد را وارد نمایید:

 

 

 

عکس شما

آپلود عکس دلخواه:








تاریخ: پنج شنبه 1 ارديبهشت 1390برچسب:,
ارسال توسط امیر عیوضی